On 2019-12-18 11:52:46
Used during TIG welding work. Although it was expensive, I was very satisfied with the welded part.
On 2018-06-07 22:39:39
Lens is not cloudy Exhaust structure is better made
Malfunction will also occur if only the light of a fluorescent light or the like does not function normally in work in dimly lit places.
It is good to wear it, it does not shift, the up and down of the surface can be adjusted on the raising side and the lower side
On 2016-04-21 20:10:05
I am using it with TIG. I think that it is easy to use if it is slightly lighter.
On 2014-10-21 14:19:48
Compared with the welding surface used before, visibility is very good and confirmation of hand is easy. The fit to the head is also good, it will not fall off. In addition, the light shielding speed is also fast and can be used with extreme peace of mind.
On 2014-10-08 13:51:13
Although I think how to compare with what I used before, I felt that the glass surface is also wide and shielding is natural so it is very useful.
TIG welding operation
On 2014-05-25 19:38:24
We used about two automatic light-shielding surfaces so far, but neither of them was good at 10,000 yen level. The 9100 V looks strange and staggeringly better than before. I noticed that it was not suitable for TIG welding as I thought now. In TIG welding it is relatively fine welding and small current, so it is difficult to make a beautiful welding around the welding spot where the light shielding degree is the lowest # 9 because it is very hard to see. As for 9100, since # 5, # 8 are selectable and the sensitivity is also digital adjustment type, it is good not to shift each time desorption. There is something that guards the light shielding window, I think that it is possible to maintain a good view at a low price if properly exchanged. There is a lens holder which can be used for hyperopic correction on the inside and a lens which is sold separately, and it can be seen better by combining it. I changed my glasses every time I welded, but it took less time and effort. It is also hard to get over pain by overtightening with a pretty invented head fastening method. Desorption property is also good and it is very smooth. However, as others point out, the function to keep the surface raised is insufficient. I do not want to overtight and break, so I am using it. Is not it better to improve to balance the weight of the face with a weak spring or something?
TIG welding, MIG / MAG welding
On 2013-10-16 20:31:35
It is good to have a wide field of view. The liquid crystal when inactive was very bright, and the frequency of raising and lowering the surface decreased. The part of the jaw is long, depending on the posture it will be shaped to catch on the throat / chest. There are a lot of adjustment mechanisms, and it is noticed that the distance from the pupil to the liquid crystal can be brought closer or further away if careful fine adjustment is made. The ability to independently adjust the holding force when raising and lowering the surface is also useful when working in a difficult posture. I think that overall it is an excellent product, but the instruction manual is too bad. Even though we have many adjustment mechanisms, there are only guides about fitting "about the things you like and put in place". I have been involved in welding for over 10 years, but I felt this side can not be used for those who do not have a habit of reading instruction manuals. Also, since the manual also does not know anything about the site, it seems to be a matter of satisfaction of the manufacturers' self-satisfaction, so it will be a pain to interpret. I want to tell 3M that there is not enough effort to tell workers the merit of the product.
Welding of aluminum, stainless steel, iron
On 2013-07-05 10:51:59
Very good with wide field of vision.
We are making SUS handrail etc.
On 2012-12-10 17:17:40
It is not comparable with what you used to ever! It is! Great. I am amazed at the brightness of the liquid crystal part before receiving light. Rarely raising the face itself has almost disappeared. One who is lost is definitely buying. (It's a bit expensive, but ...)
Semi-automatic · plasma cutting · arc welding
On 2012-04-22 23:47:49
Until now 9000 · 9002X · 9100XX purchased this time has a wider field of view than the previous screen, and there is no discomfort even if the number of face-ups between works does not decrease. The disadvantage is that fixation is bad when raising the surface. I walk down and come down. So there are times when the number of times to raise is reduced. Other than that it is perfect.