Adapters (Fastening & Drilling)

It can be attached to an impact wrench and can be used with various 6.35 mm shank sockets and driver bits of various sizes. The types of tip tools that can be used will increase dramatically.

Swing when pulled, fixed when pushed. Both can be used. High hardness HRC60 with less wear on the corners

You can use it by inserting your existing socket. A chamfer angle that allows smooth attachment and detachment. Compatible with impact drivers.

With ultra-short mug catch that does not drop the screw to the target head width 55 mm (when +2 x 33 mm double-headed bit is attached) Supports double-headed and single-headed bits for electric screwdrivers (total length 33 mm or more) 18V impact compatible Strong course thread Total length up to... Read More

You can use it by inserting your existing socket.

When the set torque is reached, a clicking sound will be heard and tightening is complete (even if more torque is applied, it will spin idle). Screws on the switchboard are recommended. Supports a bit total length of 35 mm or more. Replacement driver and drill driver can be used (impact driver ca... Read More

Easy installation of tip tools with one touch. Work efficiency is improved. Pilot hole drill Ironworking drill Double-headed bit Stepped bit Various sockets, etc.

If you put your hand on the rotating grip, you can work in a stable posture.

The torque can be adjusted in 10 steps to support delicate screw tightening. Delicate screw tightening for machines, etc.

Work in a tight position, such as tightening the screws on the back of the top plate, is easy. Work in a tight posture, such as tightening screws on the back of the top plate

Hexagon shaft parts can be used when attached to a hammer drill. It is very convenient to always have a tip tool that you use often. *Please use a tip tool with a groove position of 13 mm. *Please use in rotation mode.

Easy installation with one touch without removing the bit !! You can use both sides so you don't get lost.

Conversion adapter from hexagonal shaft 6.35 mm to square 12.7 mm. Can be switched between swinging and fixing with one touch.

Head width 60 mm (when [[(+)]] No.2 x 35 dedicated ultra-short bit is attached). Convenient for screwing, removing, and drilling in narrow corners and corners. A grip that can be firmly gripped and does not slip. By adopting a lock type bit holder, the double-headed bit can be securely attached, ... Read More

Allows difficult-to-work end mounting screws. (Minimum Sumiyose 8mm) Allows difficult-to-work end mounting screws. (Minimum Sumiyose 8mm)

"Small body" & "18V compatible" for powerful and hard work. Convenient for screwing, removing, and drilling in narrow corners and corners. It is a grip that can be firmly gripped and does not slip. The use of a lock type bit holder ensures that the double-headed bit can be... Read More

A socket adapter set that supports three types of drive angles. Various sockets can be used by attaching to an electric driver.

A 6.35 mm hex width across flats bit can be used with a 12.7 SQ mm insertion angle impact wrench. BHC-30 is a sleeve type.

Tip Tool Socket Adapter

For screwing, removing, and drilling corners, narrow spaces, and gaps! It can be used with electric impact drivers and electric screwdrivers. High torque compatible type forward / reverse rotation possible

It can be tightened to 115 N / m just by attaching it to your impact wrench. By adopting the hydraulic system for professionals, it is a stable product with little change in torque value even after long-term use.

For 6.35 mm hexagon bit. It is a C spring compatible product. * Cannot be used with the manufacturer model number EZ7552.

When changing tires, there is no need to resize the socket, which is troublesome to remove. Time can be shortened by using it in combination with an in-vehicle jack socket. To save the trouble of changing the socket size for tire replacement.

It is an adapter for changing the drive angle.

Adapter for cordless multi-driver drill GSR10.8V-15FC. Another adapter can be attached to the tip of the angle adapter. Screw tightening and drilling work on wood and metal

A round shaft cone can be used with the SDS plus hammer.

For aircraft MRO

Adapter for cordless multi-driver drill GSR10.8V-15FC. Screw tightening and drilling work on wood and metal

Flexi-click adapter Flexi-click system: You can easily and quickly change and attach adapters By changing adapters, you can handle a variety of tasks with just one unit. Can be fixed in 16 different positions (360°) Compact structure (head length: 98 mm) allows work in narrow spaces Drilling work... Read More

Supports various tasks with an impact driver! ATTACH8 (Attach Eight) Comfortable work in the corner "Sumi-uchi attachment" Can be attached in 8 directions Easy attachment / detachment! Just align the attachment with the mark and insert it. Easy operation by pressing the unlock button to... Read More

Crimp attachment for EZ1PD1

Achieves minimal backlash and friction with precision gear drive. The housing is machined from aluminum (hard anodized). For aircraft MRO

Achieves minimal backlash and friction with precision gear drive. The housing is machined from steel. For aircraft MRO