Hydraulic Valves

Balance piston type relief valve. It controls the maximum pressure of the flood control circuit and also works as a safety valve. By using the vent port, remote control of pressure and unload circuit are possible.

This is a control valve with a modularized control unit and a stacking structure.

A control valve with a modularized control unit and a stacking structure.

A control valve with a modularized control unit and a stacking structure.

It is used for remote control as a pilot valve for pilot-operated pressure control valves such as relief valves and pressure reducing valves, and for variable displacement piston pumps.

It is used for remote control as a pilot valve for pilot-operated pressure control valves such as relief valves and pressure reducing valves, and for variable displacement piston pumps.

The stack valve can be stacked on the manifold block to assemble the hydraulic unit. It is easy to change the circuit. Achieves miniaturization of hydraulic equipment.

A control valve with a modularized control unit and a stacking structure.

It is used for remote control as a pilot valve for pilot-operated pressure control valves such as relief valves and pressure reducing valves, and for variable displacement piston pumps.

By stacking on a solenoid valve and a modular stack valve, you can easily configure a circuit of 1 to 3 systems.

* Sub-plate is not attached to the valve.

It is mainly used to control the speed of the actuator. For one-sided flow, it has the same function as the throttle valve, and for reverse flow, it becomes a free flow that allows a large amount of flow to flow through the check valve. It is best used for small machines such as machine tools.

The world's highest level of high voltage, large flow rate, and low voltage loss have been achieved by rational flow path design including a powerful wet type solenoid and a 5-chamber system.

The Dester valve is an adjustable resistance distributor that can be used for both intermittent and continuous refueling, and is a product with high advantages of simplicity and economy. When the oil pumped from the pump is branched and sent to each refueling point, the flow rate can be adjusted ... Read More

A valve that allows oil to pass freely in one direction with a given cracking pressure and completely blocks the flow in the opposite direction.

The Dester Plunger is a quantitative distributor that discharges only a preset discharge amount by the pressure from the pump. Used with first-out type positive displacement distributors and positive displacement pumps

It can be used as a stop valve for pressure gauge pipelines or small-capacity pipelines, and can also be used as a throttle valve that regulates diversion of pilot pipelines.

It is installed in the line in the axial direction, and when the cracking pressure is reached, the check valve is pushed open, oil flows in only one direction, and the flow in the opposite direction is blocked. * Install so that the entrance (IN) is on the bottom.

A wide range of pressure adjustment is possible, and pressure adjustment in the low pressure range is also easy. * Connect the tank piping directly to the tank without merging with other tank piping. * For stable pressure control, loosen the air bleeding screw, bleed the air sufficiently, and fil... Read More

Since the movable iron core of the solenoid is a wet type solenoid that is lubricated and buffered in oil, there is little wear and it has a long life. Since it is a wet solenoid, the switching noise of the movable iron core is very low, and the operation is really quiet. High pressure and large ... Read More

It is a compact design. High pressure and large capacity. The rated flow rate has been increased. Increased allowable back pressure. The lamp and ground terminal are standard equipment. The surge killer is standard equipment.

Since the movable iron core of the solenoid is a wet type solenoid that is lubricated and buffered in oil, there is little wear and it has a long life. Since it is a wet solenoid, the switching noise of the movable iron core is very low, and the operation is really quiet. High pressure and large ... Read More

It is a stop valve developed for a pressure gauge that monitors the pressure of a hydraulic circuit. We also have a type that can be fixed to the stand, the orientation of the pressure gauge can be corrected, and the pressure gauge can be directly attached. With a pressure shutoff handle (SA / S ... Read More

An epoch-making high-pressure, large-flow electromagnetic switching valve developed by incorporating a novel design concept everywhere, including the solenoid part. As it is a wet type, it has a long life, low noise, and no oil leakage to the outside.