Plug Type Heaters
A plug-type heater is a highly efficient heater that can heat liquid directly. It is easy to install and features a small space. There are water heaters and oil heaters, both of which are equipped with a protective tube for the sensor, so equipment parts for preventing the temperature controller from rising can be installed. Stainless steel flange heaters are used to heat water, oil and cleaning fluid. Various heaters with power from 2kw to 5kw are available.
Other Related Pages
Sakaguchi E.H VOC Compression fittingIt is a mounting part for the T35 type sheath thermocouple.- HAKKO (Hakko Electric) Plug type heaterWith a protective tube for the sensor, equipment parts such as temperature controller overheating prevention can be easily attached. Since it is easy to install and handle and requires less installation space, the equipment cost is low and the structure is robust, so you can use it with confidenc... Read MoreDimension B (mm) 25 Material (Heater Sheath) C1220T (copper tube) nickel plating Protective Tube C1220T (copper tube) nickel plating Plug FC250 (iron casting) nickel plating Specification For water Material (Gasket) Non-asbestos (t1.5) Cap SPCC (paint)
- Watlow Miniature connectorThermocouple connector that uses the American National Standards Institute (ANSI) color code. Excellent heat and impact resistance. High-quality connectors with a compact design that take up little space and strong contact pressure. * Plugs and jacks are not sold as a set.Heat Resistance Temperature (℃) 200
- Sakaguchi E.H VOC Space heater (lead type)* Since all exteriors are made of bonded steel plate, please adjust the temperature so that the maximum operating temperature on the heater surface is below 300 ° C. * If the surface temperature of the heater exceeds 400 ° C, rust may occur on the bare metal due to thermal deterioration of the zi... Read Morefrom S$24.99Min. 2 days
- Sakaguchi E.H VOC Coats heaterThe coats heater is a heating method that uses near-infrared radiation. More than 85% of the input power becomes infrared rays and heats efficiently. The standard heater is manufactured so that the color temperature is 2500K, and the infrared wavelength region has a peak wavelength of about 1.2 μ... Read MoreMaximum Resistant Temperature (℃) (Terminal) 200 Color Temperature (K) 2500 Specification Terminal: Heat-resistant lead wire
- Sakaguchi E.H VOC Far-red ceramic heater standard [S-II type]By adopting a high-efficiency radiator, the heating and drying time can be shortened. Since it is a planar heating element with a uniform temperature distribution, it can be heated uniformly. Accurate temperature control is possible, and block-by-block control is possible. By using the sensor bui... Read MoreSpecification (Center wavelength) 6.15-3.75μm Tensile Strength (kg) (Lead wire) 15 Highest Temperature (℃) (Surface) 500 Service Life 10,000 hours or more Insulation Resistance (MΩ) 1000 or more Dielectric Breakdown Voltage (kV) 4 or more Time to Stabilize (min) 6～8from S$97.99Min. 2 days
-
- Sakaguchi E.H VOC K type Φ0.5 sheathed thermocouple with flexible compensating lead wire (Max.The flexible fluororesin (exodermis) compensating lead wire has excellent flexibility, heat resistance, cold resistance, flame resistance, and chemical resistance, making it suitable for wiring to moving parts such as injection molding machines and robots. The entire thermocouple, including the s... Read MoreLength (mm) (Compensation conductor) 1000 Heat Resistance Temperature (℃) (Compensation lead) 200 Regular Temperature (℃) 500 Sleeve Dimensions (Φmm × mm) 6.5×30 Tolerance Class 1 Compensation lead Flexible fluororesin Wire Type K type Material (Sheath) SUS316 Contact Ungroundedfrom S$199.90Min. 2 days
- Sakaguchi E.H VOC Coat heater holderA holder (metal fitting with insulator) for fixing the heater.
- Sakaguchi E.H VOC Reflective shade for far infrared heaterA reflective shade for far-infrared heaters. By using a reflective shade, the irradiation range of infrared energy radiated from the heater can be concentrated and the heating efficiency can be improved. Heating efficiency can be improved by attaching it to a far-infrared heater. * If the tempera... Read Morefrom S$77.99Min. 6 days
- HAKKO (Hakko Electric) Ultra W Stainless sheath typeCompact, high capacity, water cartridge heater that can be installed in any space. It can be installed in a small space and can be heated with high thermal efficiency and little loss. It is a heater for water heating using "Ultra Five" which is well-established as a cartridge heater. It... Read MoreDensity of Effective Heating Area (W/cm2) 7
- HAKKO (Hakko Electric) Plug Type HeaterSince it has a protective tube for the sensor, device parts such as temperature controller overheating prevention can be easily attached. Since it is easy to install and handle and requires less installation space, the equipment cost is low and the structure is robust, so you can use it with conf... Read MoreMaterial (Gasket) Non-asbestos (t1.5) Cap SPCC (paint) Specification For waterfrom S$699.90Min. 5 days
- HAKKO (Hakko Electric) Ultra W copper sheath typeCompact, high capacity, water cartridge heater that can be installed in any space. It can be installed in a small space and can be heated with high thermal efficiency and little loss. It is a heater for water heating using "Ultra Five" which is well-established as a cartridge heater. It... Read MoreDensity of Effective Heating Area (W/cm2) 15from S$229.90Min. 5 days
- Yagami Inc. Plug Heater LAG TypeThe wetted parts are all made of stainless steel, achieving a long life. The plug has a solid structure with stainless casting by the lost wax method. It is necessary to use it together with the separately sold temperature controller. * As a general rule, it is installed horizontally. * It is nec... Read MorePart No. 1084616 Ambient Temperature (℃) 10～60 Density of Effective Heating Area (W/cm2) 2.5 Voltage (V) 200 Voltage 200V three phase Capacity (W) 3000 Dimension L (mm) 580 Ambient Humidity (% RH) 85 or lessfrom S$479.90Min. 27 days
- Watlow Standard connector [plug]Thermocouple connector that uses the American National Standards Institute (ANSI) color code. It has excellent heat and impact resistance and is easy to install. * Plugs and jacks are not sold as a set.Dimension (mm) (Pin spacing) 11.1 Heat Resistance Temperature (℃) 215 Dimension (Φmm) Pin: (+) 3.97, (-) 4.78
- Sakaguchi E.H VOC Far-red ceramic heater standard [S-I type]By adopting a high-efficiency radiator, the heating and drying time can be shortened. Since it is a planar heating element with a uniform temperature distribution, it can be heated uniformly. Accurate temperature control is possible, and block-by-block control is possible. By using the sensor bui... Read MoreSpecification (Center wavelength) 6.15-3.75μm Tensile Strength (kg) (Lead wire) 15 Highest Temperature (℃) (Surface) 500 Service Life 10,000 hours or more Insulation Resistance (MΩ) 1000 or more Dielectric Breakdown Voltage (kV) 4 or more Time to Stabilize (min) 6～8from S$129.90Min. 6 days
- HAKKO (Hakko Electric) Ultra W 800Compact, high capacity, water cartridge heater that can be installed in any space. It can be installed in a small space and can be heated with high thermal efficiency and little loss. It is a heater for water heating using "Ultra Five" which is well-established as a cartridge heater. It... Read MoreDensity of Effective Heating Area (W/cm2) 20 Pipe Parallel Thread Nominal Size R1/2 Power Cable Silicone rubber cabtyre cord 300mm Voltage (V) Three-phase 220from S$329.90Min. 5 days
- Sakaguchi E.H VOC Movable flangeIt is a mounting part for the T35 type sheath thermocouple.from S$12.99Min. 6 days
- HAKKO (Hakko Electric) Plug heater Stainless steel sheath Standard typeWith a protective tube for the sensor, equipment parts such as a temperature controller and overheating prevention can be easily installed. The equipment cost is low because it is easy to install and handle and requires less installation space. Moreover, it is structurally robust, so you can use ... Read MoreDensity of Effective Heating Area (W/cm2) 7.5from S$639.90Min. 5 days
- Sakaguchi E.H VOC [For oil heating] Plug heater (OP type)Dimension C (mm) 15 Dimension B (mm) 23 Voltage (V) Single phase / Three phase 200from S$229.90Min. 6 days
- HAKKO (Hakko Electric) Plug heater copper sheath standard typeWith a protective tube for the sensor, equipment parts such as a temperature controller and overheating prevention can be easily installed. The equipment cost is low because it is easy to install and handle and requires less installation space. Moreover, it is structurally robust, so you can use ... Read MoreDensity of Effective Heating Area (W/cm2) 10 Dimension B (mm) 25 Voltage (V) Three-phase 200from S$439.90Min. 5 days
- HAKKO (Hakko Electric) Plug type heaterSince it has a protective tube for the sensor, device parts such as temperature controller overheating prevention can be easily attached. Since it is easy to install and handle and requires less installation space, the equipment cost is low and the structure is robust, so you can use it with conf... Read MoreCap SPCC (paint) Material (Gasket) Asbestos (t1.5) Specification For oil Plug FC250 (iron casting) nickel plating Voltage (V) Three-phase 200 Material (Heater Sheath) STKM11A (steel pipe) nickel plating Protective Tube STKM11A (steel pipe) nickel platingfrom S$469.90Min. 5 days
- HAKKO (Hakko Electric) Ultra W for seawaterPure titanium is used for the sheath, which has excellent corrosion resistance and is ideal for heating seawater and chemicals. Due to its light weight, it is easy to handle during installation. As it comes with a plug, it can be securely attached to the tank. It has a long life and is a robust d... Read MoreWire cross section (mm 2 ) 0.75 Density of Effective Heating Area (W/cm2) 5 Material Heater sheath plug: Titanium Pipe Parallel Thread Nominal Size R1/2from S$489.90Min. 5 days
- HAKKO (Hakko Electric) Ultra WLThe stainless steel sheath (SUS316L) has excellent corrosion resistance. It can also be used for liquids other than oil (liquids that do not corrode stainless steel) such as alkaline solutions. A compact oil cartridge heater that can be installed in any space. It can be installed in a small space... Read MoreWire cross section (mm 2 ) 0.75 Density of Effective Heating Area (W/cm2) 2.5 Pipe Parallel Thread Nominal Size R3/4from S$489.90Min. 5 days
- Sakaguchi E.H VOC [For Water Heating] SUS Plug Heater (SOP Type)Dimension C (mm) 15 Dimension B (mm) 23 Voltage (V) Single phase / Three phase 200from S$379.90Min. 6 days
- Sakaguchi E.H VOC Far-red ceramic heater standard [S-Ⅲ type]By adopting a high-efficiency radiator, the heating and drying time can be shortened. Since it is a planar heating element with a uniform temperature distribution, it can be heated uniformly. Accurate temperature control is possible, and block-by-block control is possible. By using the sensor bui... Read MoreSpecification (Center wavelength) 6.15-3.75μm Tensile Strength (kg) (Lead wire) 15 Highest Temperature (℃) (Surface) 500 Service Life 10,000 hours or more Insulation Resistance (MΩ) 1000 or more Voltage (V) 200 Dielectric Breakdown Voltage (kV) 4 or more Time to Stabilize (min) 6～8from S$129.90Min. 6 days
- HAKKO (Hakko Electric) Plug heater for cleaning liquidWhen heating the cleaning liquid, the boiling point rises as the oil content in the liquid increases, and the heater surface temperature also rises. The surface temperature of the heater rises more and more. This causes the cleaning solution to pyrolyze and eventually begin to corrode the heater ... Read MoreProtective Tube, Inner Diameter x Effective Length (Φmm x mm) 10×115 Density of Effective Heating Area (W/cm2) 4.5 Temperature Controller Type B、A3 Pipe Parallel Thread Nominal Size G2 Voltage (V) Three-phase 200from S$599.90Min. 5 days
- Sakaguchi E.H VOC Far red ceramic heater hollow [S-2 (II) type]By adopting a high-efficiency radiator, the heating and drying time can be shortened. Since it is a planar heating element with a uniform temperature distribution, it can be heated uniformly. Accurate temperature control is possible, and block-by-block control is possible. By using the sensor bui... Read MoreSpecification (Center wavelength) 6.15-3.75μm Tensile Strength (kg) (Lead wire) 5 Highest Temperature (℃) (Surface) 500 Service Life 10,000 hours or more Insulation Resistance (MΩ) 1000 or more Voltage (V) 200 Dielectric Breakdown Voltage (kV) 4 or more Time to Stabilize (min) 4～6from S$119.90Min. 6 days
- Sakaguchi E.H VOC Far-red ceramic heater with thermocouple [S-3 (Ⅲ) type]By adopting a high-efficiency radiator, the heating and drying time can be shortened. Since it is a planar heating element with a uniform temperature distribution, it can be heated uniformly. Accurate temperature control is possible, and block-by-block control is possible. By using the sensor bui... Read MoreSpecification (Center wavelength) 6.15-3.75μm Tensile Strength (kg) (Lead wire) 15 Highest Temperature (℃) (Surface) 500 Capacity (kW) 0.4 Service Life 10,000 hours or more Insulation Resistance (MΩ) 1000 or more Voltage (V) 200 Dielectric Breakdown Voltage (kV) 4 or more Time to Stabilize (min) 6～8 Thermocouple K typefrom S$159.90Min. 6 days
- HAKKO (Hakko Electric) Flange heater Copper sheath JIS Nominal diameter 80 Flange typeWith a protective tube for the sensor, equipment parts such as a temperature controller and overheating prevention can be easily installed. Equipment costs are low because it is easy to install and handle and requires less installation space. Moreover, it is structurally robust, so you can use it... Read MoreProtective Tube, Inner Diameter x Effective Length (Φmm x mm) 10×115 Density of Effective Heating Area (W/cm2) 7.5 Temperature Controller Type B、A3 Voltage (V) Three-phase 200from S$779.90Min. 5 days
- HAKKO (Hakko Electric) Plug heater Stainless steel sheath Sealed typeWith a protective tube for the sensor, equipment parts such as a temperature controller and overheating prevention can be easily installed. The equipment cost is low because it is easy to install and handle and requires less installation space. Moreover, it is structurally robust, so you can use ... Read MoreDimension C (mm) 17 Dimension B (mm) 23 Dimension D (mm) 62 Density of Effective Heating Area (W/cm2) 7.5 Dimension E (mm) 71 Pipe Parallel Thread Nominal Size G2 Voltage (V) Three-phase 200 Specification With drip-proof capfrom S$1,099.00Min. 5 days
- Sakaguchi E.H VOC Far-red ceramic heater with thermocouple [S-1 (Ⅰ) type]By adopting a high-efficiency radiator, the heating and drying time can be shortened. Since it is a planar heating element with a uniform temperature distribution, it can be heated uniformly. Accurate temperature control is possible, and block-by-block control is possible. By using the sensor bui... Read MoreSpecification (Center wavelength) 6.15-3.75μm Tensile Strength (kg) (Lead wire) 15 Highest Temperature (℃) (Surface) 500 Service Life 10,000 hours or more Insulation Resistance (MΩ) 1000 or more Voltage (V) 200 Dielectric Breakdown Voltage (kV) 4 or more Time to Stabilize (min) 6～8 Thermocouple K typefrom S$159.90Min. 6 days
- Sakaguchi E.H VOC Stainless steel plate flange heaterThe heater is made entirely of stainless steel, including the flange. It has excellent corrosion resistance, has a long life, and is ideal for water heating. The heater uses a JIS standard flange. It can be easily installed and installed. Since it has a sensor protection tube, it is easy to preve... Read MoreMaximum Operating Temperature (℃) 100 Isolation Voltage 1500V AC / 1 minute Insulation Resistance (MΩ) 20 or more with DC500V insulation meter Dimension A (mm) 50 Voltage (V) Three phase 200 Heater Φ12×3from S$599.90Min. 6 days
- HAKKO (Hakko Electric) Flange heater Copper sheath JIS Nominal diameter 50 Flange typeWith a protective tube for the sensor, equipment parts such as a temperature controller and overheating prevention can be easily installed. Equipment costs are low because it is easy to install and handle and requires less installation space. Moreover, it is structurally robust, so you can use it... Read MoreProtective Tube, Inner Diameter x Effective Length (Φmm x mm) 10×115 Density of Effective Heating Area (W/cm2) 7.5 Temperature Controller Type B、A3 Voltage (V) Three-phase 200from S$699.90Min. 5 days
- HAKKO (Hakko Electric) Temperature control plug heater stainless steel sheath typeA liquid-inflated thermostat is built into the cap, making it easy, convenient, and space-saving. A cabtire cable is standard equipment. Since it generates heat in water, it has better thermal efficiency than indirect heating from the outside of the container. * Due to the structure of the temper... Read MoreTemperature Control Range (℃) 30～120 Density of Effective Heating Area (W/cm2) 7.5 Pipe Parallel Thread Nominal Size G2 Voltage (V) Three-phase 200from S$1,399.00Min. 5 days
- HAKKO (Hakko Electric) Flange heater Oil iron seriesDensity of Effective Heating Area (W/cm2) 2.5 Pipe Parallel Thread Nominal Size G3/4 Voltage (V) Three-phase 200from S$779.90Min. 5 days
- HAKKO (Hakko Electric) Flange heater Oil iron seriesDensity of Effective Heating Area (W/cm2) 2.5 Pipe Parallel Thread Nominal Size G3/4 Voltage (V) Three-phase 200 Heater Φ12 × 3 pcsfrom S$699.90Min. 5 days
- HAKKO (Hakko Electric) Plug heater Copper sheath Outdoor type (Built-in thermal fuse)With a protective tube for the sensor, equipment parts such as a temperature controller and overheating prevention can be easily installed. The equipment cost is low because it is easy to install and handle and requires less installation space. Moreover, it is structurally robust, so you can use ... Read MoreThermal Fuse 128℃ 10A Density of Effective Heating Area (W/cm2) 7.5 Pipe Parallel Thread Nominal Size G2 Voltage (V) Three-phase 200 Heater Φ10 × 3 pcsfrom S$1,199.00Min. 5 days
- Sakaguchi E.H VOC Coat heater skirtReflective shade for coats heater. By using a reflective shade, the irradiation range of infrared energy radiated from the heater can be concentrated and the heating efficiency can be improved. Heating efficiency can be improved by attaching it to a coats heater. * Coates heater [NSK type] cannot... Read Morefrom S$24.99Min. 6 days
- Yagami Inc. Sheath heater LUB type for liquid heatingAll wetted parts are made of stainless steel, which has high corrosion resistance and long life. The bushing is also made of stainless steel, making it resistant to corrosion. * Since it is designed for liquid heating, if the heat generating part is exposed in the air and it is heated in the air,... Read MoreAmbient Temperature (℃) 10～60 Ambient Humidity (% RH) 85 or lessfrom S$249.90Min. 2 days
![Far-red ceramic heater standard [S-II type]](https://jp.images-monotaro.com/Monotaro3/pi/middle/mono18448624-180426-02.jpg)
![[For water heating] Plug heater (HP type)](https://jp.images-monotaro.com/Monotaro3/pi/middle/mono70757855-171120-02.jpg)
![Standard connector [plug]](https://jp.images-monotaro.com/Monotaro3/pi/middle/mono18448895-180426-02.jpg)
