Chamfering / Deburring
There are machining methods such as chamfering and deburring. Chamfering is a work that cuts off the corners after metal processing. This is called “chamfering” because the surface is created by cutting off the corners using a special chamfering cutter. In addition, burrs are unintentionally produced at the corners of a material when cutting or scraping the material. If burrs are left as they are, the appearance of the product will be damaged, and touching may cause injury or damage to other parts, so it must be scraped off with a file or rotating blade. This is called deburring.
- TRUSCO Nice Men G (Chamfering Cutter)Longer life due to titanium coating. Beautiful surface finish without chattering. Smooth surface finish with a single blade.Chamfer Angle 90° Blade Shape Others Material SKH-51 (High Speed)
- TRUSCO Counter SinkCobalt high-speed steel is used as the base material, and it has excellent wear resistance and heat resistance. By adopting a 3-flute shape for the cutting edge, chips can be discharged well and a beautiful finish can be obtained. Work material: Iron, casting, stainless steel. chamfer. Deburring.... Read MoreNumber of Tips 3 Blade Shape 3 blades Tip Angle (°) 90 Chamfer Angle 90° Material Cobalt high speed steel (HSS-Co) Surface Treatment Non-coated
- Walter Tytex counter sink (titanium coating)It is a unique design that suppresses chattering and has excellent centripetal properties. It has excellent sharpness and excellent chip evacuation. Work Material: Steel, Alloy Steel, Casting, Stainless Steel, Copper Alloy, Aluminum Alloy. Chamfering, counterbore, deburring.Number of Tips 3 Specification 3 blades Blade Shape 3 blades Tip Angle (°) 90 Material High speed steel (HSS) Surface Treatment Titanium coatingfrom S$46.99Min. 2 days
- THECUT Chamfering Cutter KIRIMAN MTMBWith a special insert and a unique body structure, it has excellent sharpness and does not chatter. By using special steel for the body, it has excellent wear resistance and durability. It has good bite and centripetal properties, and can be easily worked on a drilling machine. The insert is repl... Read MoreNumber of Tips 1 Dimension l2 (mm) 50
- Tominaga Kosakusho Plastic / aluminum chamfering machine EcoscutHigh speed and high accuracy even though it is manual! It is possible to chamfer 12 edges of blocks of 50 x 50 x 20 size in about 30 seconds. It doesn't get scratched, it doesn't take up much space, the chamfered surface is shiny and quiet, and there is little scattering of chips. Chamfer... Read MoreBlade Shape Othersfrom S$2,299.00Min. 4 days
- FUJIGEN KOGYO Ulatrimen-CFor "back" only! A special tool specializing in backside machining.Number of Tips 1 Blade Shape 1 blade Dimensions ls (mm) 70from S$269.90Min. 5 days
- MonotaRO Center Drills 60 °A tool suitable for machining center holes. Since the groove length of the drill itself is short, it is rigid. Compared to ordinary short type drills, the blade shape is less likely to shift, so it can also be used for positioning when drilling with a drill. For machining and positioning of cente... Read MoreTip Angle (°) 60 Material Hss Coating None
- NOGA Nogabar 3Unique handle that can hold all S blades. The handle part can be used to store the spare blade. The blade replacement button is designed so that it cannot be removed without raising the nail for safety. The back cap is also designed so that it will not come off during work.
- JEFCOM (DENSAN) Round and round reamerChamfering and deburring can be done easily After making holes with a hole saw, various shapes such as chamfering, iron, stainless steel, copper, aluminum, plastic pipes (inner and outer surfaces), plates (side surfaces), drill holes, etc. Convenient for chamfering and deburring work in narrow sp... Read MoreOverall Length (mm) 125 Mass (g) 40
- MonotaRO NC spotting drill 90 ° TiN coatingCentering (rubbing) before drilling and chamfering can be performed at the same time. By adopting TiN coating, it has a longer life and is suitable for more work materials than non-coated products. When processing hole chamfering and centering (rubbing) at the same time. * Be sure to wear protect... Read MoreTip Angle (°) 90 Material Hss Co 5% Coating TiN
- MonotaRO Countersink Handy TypeYou can manually chamfer holes and deburr. For chamfering and deburring. * Do not use for any purpose other than its intended purpose. * Be careful of chips. * Do not touch the blades and chips directly.Chamfer Angle 90° Overall Length (mm) 162 (including blade), 141 (grip only) Pattern Width (mm) 28.5 Material PP + TPR (grip), M2 (blade) Included Accessories Spanner x 1 Mass (g) 94 (including blade), 74 (grip only) Range to Use (mm) 3-20
- WORK FINISHER Ceramic Deburring ToolIdeal for deburring hard plastic molded products such as those containing glass, carbon fiber, and talc, which were difficult in the past. It is also suitable for burrs and chamfering of non-ferrous metals such as aluminum, brass, and copper. Since it does not have a blade, it is safer than conve... Read MoreBlade Thickness (mm) 1.5 Material (Blade) Ceramic Blade Angle (°) R30 Material (Body) plastic
- SK (Niigata Seiki) Chamfer CutterIt can be used for various purposes such as chamfering, deburring, and widening holes. For iron, aluminum, brass, copper, wood, etc.Shank Diameter (Φmm) 6 Number of Tips 7 Chamfer Angle 90° Material High-speed steel (SKH) Blade Shape Others
- MonotaRO Center drill 90 °A tool suitable for machining some center holes. Since the groove length of the drill itself is short, it is rigid. Compared to a normal short type drill, the blade shape is less likely to shift, so it can also be used for positioning when drilling with a drill, and the tip is 90 °, so it can als... Read MoreTip Angle (°) 90 Material Hss Coating None
- YAMAWA Strong Helix Groove A Type 60° Center Hole Drill for Mer JIS1 Type CE-S* If you order by cash on delivery, it may be shipped the next day or later.
- H&H Hex shaft chamfering cutterIt can also be used for countersunk and pipe chamfering wood when tightening wood screws, light metals such as aluminum and copper, and mild steel materials that have not been hardened. * Please use the drill speed at 5000 rpm or less.Material High-grade carbon tool steel Blade Shape Others
- STAR-M No.5007X Chamfering cutter for stainless steelFor chamfering and deburring after drilling holes in metal materials. Chamfering cutter for stainless steel!] Ideal for deburring and chamfering after drilling a metal material! Since it is a perforated type chamfering cutter, chips can be removed smoothly! The material is HSS-CO and highly durab... Read MoreProper rotation speed (min -1 ) 2000 or less Blade Angle (°) 90 Material HSS-CO Shank Diameter (Φmm) Hex axis 6.35 Blade Shape Others Suitable Material Stainless steel / Iron Nonferrous metal
- MonotaRO Center drill 60 ° TiAlCN coatingA tool suitable for machining center holes. Since the groove length of the drill itself is short, it is rigid. Compared to ordinary short type drills, the blade shape is less likely to shift, so it can also be used for positioning when drilling with a drill. By adopting TiAlCN coating, it has a l... Read MoreTip Angle (°) 60 Material HssE 5% Coating TiAlCN
- NT Tool Chamfer CutterFor processing soft and sticky materialsBlade angle a (°) 90 Chamfer Angle 90° Blade Shape Others
- NOGA Double Bar DB1000Since it uses a round blade, it has a long life if you use it while shifting the blade little by little, and you can use it twice as long if you use the other side as well. Comes with a hand guard to protect your hands. When chamfering the corners, use only one round blade.Trusco Part No. 111-3976 Maximum Thickness (mm) 12 (The blade width can be adjusted.) Mass (g) 178
- STAR-M No.5007 High-speed Hexagonal Shaft Chamfering CutterIdeal for chamfering and deburring countersunk screws. High durability with high-speed steel for deburring and chamfering after drillingFlute Length (mm) 32 Suitable Material Aluminum, iron, resin, wood Shank Diameter (Φmm) Hex axis 6.35 Blade Shape Others
- HIT Mentori (Chamfering) for PVCBy adopting a soft grip, it is easy to apply force, and the outside and inside of the PVC pipe can be chamfered at the same time. Chamfering of water supply pipes and drainage pipes of PVC pipes.Mass (g) 160 Overall Length (mm) 170 Material / Finish (Blade) Hard steel wire rod Trusco Part No. 254-2439 Suitable Pipe 40A~250A
- SK Hexagonal chamfering cutterA 7-blade chamfering and deburring cutter. For chamfering, deburring, and expanding holes in iron, aluminum, brass, copper, wood, etc.Shank Diameter (Φmm) 6.35 Blade Shape Others Shank Shape hexagonal
- Tsubosan Deburring knifeIdeal for deburring plastic and metal. There are right-handed and left-handed. * If it is clogged, remove it with a brush etc. before use.Blade Length (mm) 37 Suitable Material Plastic, metal, etc. Overall Length (mm) 162
- Okabe Kougu Center Drill Type 1Surface Treatment - Tip Angle (°) 60 Material High-speed steel (SKH51)
- YAMAWA Long Shank Strong Helix Groove A Type 60° Center Hole Drill CE-SLSince the groove has a strong twist, it is suitable for relatively sticky materials (SUS, etc.) or especially soft materials.Material High speed steel HSS Surface Treatment Non-coated
- TRUSCO Counter sink titanium coatingCobalt high-speed steel is used as the base material, and it has excellent wear resistance and heat resistance. The surface hardness is high due to the surface titanium coating treatment, and heat resistance, wear resistance and sharpness are improved compared to cobalt highs. chamfer. Deburring.... Read MoreBlade Shape 3 blades Tip Angle (°) 90 Blade Angle (°) 90 Chamfer Angle 90° Material Cobalt high speed (HSS-CO) Abrasive Materials Iron, casting, stainless steel Number of Tips Three Surface Treatment Titanium coatingfrom S$39.99Min. 2 days
- NOGA Rapid barAll S blades (3.2mm shaft) can be installed. The housing that holds the blade is made of steel, so it can be used semi-permanently. To replace the blade, push on the sleeve of the housing and attach / detach the blade.Mass (g) 58 Handle Dimensions (mm) About 12 × 130 Trusco Part No. 111-3216 Suitable Shaft Diameter (Φmm) 3.2
- TRUSCO Hexagon Axis Nice Men G 3 Flute 6mm Titanium CoatingThe hexagonal shaft (6.35 mm) is ideal for C chamfering and deburring in field work. Since the blade is coated with titanium, burr welding to the blade is reduced. It has a long life. The three-flute provides a stable cutting balance with good cutting balance and little chatter. Work material: Al... Read MoreTip Diameter (Φmm) 1 Number of Tips 3 Blade Shape 3 blades Specification 3 blades Shank Diameter (Φmm) 6.35 Tip Angle (°) 90 Material High speed steel (HSS) Surface Treatment Titanium coatingfrom S$38.99Min. 2 days
- FUJIGEN KOGYO MentorubyExcellent sharpness with a high-speed tip with a breaker. Since the tip is replaceable, there is no need for re-polishing. * The capacity value is the value when TM32GUR is installed. When using TM32GSR, the maximum processing diameter is reduced by about 2 to 3 mm.Blade Shape 1 blade Number of Tips 1 sheet Suitable Tip TM32GUR HSS、TM32GSR HSS
- TRUSCO Hexagon Axis Nice Men G 1 Flute 6mm Titanium CoatingThe hexagonal shaft (6.35 mm) is ideal for C chamfering and deburring in field work. A smooth chamfered surface finish is possible with a single blade. Since the blade is coated with titanium, burr welding to the blade is reduced. It has a long life. Work Material: Aluminum, Iron, Resin, Copper, ... Read MoreTip Diameter (mm) 1 Type 1 blade Shank Diameter (mm) 6.35 Tip Angle (°) 90 Blade Shape Others Surface Treatment Titanium coating
- NOGA Cobalt High Speed Counter SinkThe hardened material is CBN polished to form a sharp blade without burrs. It also has higher dimensional accuracy and achieves a long life. It also gives good results at relatively slow cutting speeds. Suitable for high chrome alloy steels such as stainless steelNumber of Tips 3 Blade Shape 3 blades Tip Angle (°) 90 Material Cobalt high speed (HSS-CO) Surface Treatment Non-coated
- NOGA Noga BarThe most versatile and economical. All 3.2mm shaft S blades can be attached to the NB handle.Suitable for 3.2mm axis compatible
- YAMAWA Titanium Coating Center Drill 60 °Since the twist of the groove is strong, it is suitable for relatively sticky materials (such as SUS) or particularly soft materials. TiN coating with excellent wear resistance is applied.
- YAMAWA 90° NC-SD V for NC starting drill chamferingThe highly rigid design enables stable and highly accurate positioning and chamfering. It has good biting properties and is effective for positioning curved surfaces and gentle slopes that are difficult to process.
- MonotaRO Center drill 90 ° TiAlCN coatingA tool suitable for machining some center holes. Since the groove length of the drill itself is short, it is rigid. Compared to a normal short type drill, the blade shape is less likely to shift, so it can also be used for positioning when drilling with a drill, and the tip is 90 °, so it can als... Read MoreTip Angle (°) 90 Material Hss Coating TiAlCN
- JEFCOM (DENSAN) Round and round reamer spare bladeSpare blade for reamer that can easily perform chamfering and deburring work
Filter by categories