Corrosion resistant oil rotary vacuum pump for in-line chemical type.
* The internal filter element cannot be replaced. * A clamp joint is required to install the pump.
Prevents contamination by liquids, aerosols, etc., which are problems with suction devices such as suction pumps and aspirators.
For protection of vacuum pump as a filter on the inlet side. As a filter on the outlet side, it prevents the scattering of solvent and oil mist due to the exhaust of th... Read More
Moisture retention capacity 0.09MPa (14psi) max. Withstand Pressure (MPa) 0.1(15psi) Particle Retention Capacity (μm) 0.1μm 99.9% As ONE Part Number 1-5699-01 Effective filtration area (cm2) 16 Connection Size 6-10mm ID stepped hose opening Dimension (mm) Φ53×46
Dry air with an atmospheric dew point of -10 ° C can be obtained. It can be used with a small compressor (small flow rate). There are 3 types of combinations.
As ONE Part Number 1-5052-02 Mass (kg) 1.9 Ultimate Pressure (kPa) 16 Dimension (mm) 164 x 90 x 141 (excluding protrusions) Maximum Discharge Pressure 250kPaG Suitable Tube Inner Diameter (Φmm) 4 Operating Temperature (℃) 40 Maximum air flow (L / min) 5.5 Power Supply AC100V 50/60Hz 70W 1.8A Specification Built-in thermal protector
This is a basic pump head. Up to 4 can be connected. The case is a polycarbonate molded product with excellent impact resistance. It is used as a liquid feed pump by setting it with the motor drive unit and tube.
Flow Rate (mL/min) (Min) 0.8, (Max) 480 Trusco Part No. 466-2580 Mass (kg) 0.5 Suitable for (Tube No.) 16
A low vacuum (≧ 100 Pa) air filter attached to the intake port of a rotary vacuum pump. Collects particles, dust, and contamination generated in the vacuum exhaust line. The element is made of polyester and collects 99% or more with 5 μm. Since the element is L-shaped, it can be easily replaced w... Read More
Negative pressure can be applied to the inside of the bottle to collect directly from the tube into the bottle, and cross-contamination can be prevented by exchanging the tube and container.
The exhaust air tube is equipped with HEPACAP, which has a dust collection efficiency of 99.97% or more with 0.3 μm particles as a measure against biohazard. Since the inside of the collection container lid has a barb, it is difficult for the collected liquid to be sucked into the pump side. The ... Read More
Suction Capacity 12/14L/min(50/60Hz) Dimensions, Diameter x Height H (Φmm x mm)Φ Collection container: 128 × 280 Power Supply AC100V 50/60Hz 0.50/0.44A Material Collection container: Glass Capacity (L) Collection container: 2 (full 1.2)
It is possible to send strong acids, strong alkalis, and organic solvents. Ideal for sending organic solvents and corrosive solutions, filtering, and injecting chemicals. The life of the pump tube is about 500 hours (at 21 ° C, pressure 0, rotation speed 100 rpm). The wetted part is only the pump... Read More
Material (Main body) Aluminum, (Roller) SUS Recommended Operating Speed (min-1 [rpm]) 1～300 Suction Head (m) 2.4 (for water) Outer Dimensions, Width W x Depth D x Height H (mm) 84×68×140 Maximum pressure (kPa) 689
Negative pressure can be applied to the inside of the bottle to collect directly from the tube into the bottle, and cross-contamination can be prevented by exchanging the tube and container.
ULVAC Oil Mist SeparatorCorrosion resistant oil rotary vacuum pump for in-line chemical type. * The internal filter element cannot be replaced. * A clamp joint is required to install the pump.from S$589.90Min. 2 days
