If the LM rail mounting holes of the LM Guide are clogged with chips or foreign matter, they may enter the inside of the LM block. In such a case, the LM rail mounting hole can be closed with a special cap to prevent foreign matter from entering. The C type cap for the LM rail mounting hole uses ... Read More
It is a plate to align the height of [[MK]] [[MKS]] [[HK]] with the height of the carriage. It may be required depending on the combination of [[MK]] [[MKS]] [[HK]] and the linear guideway. Please check the selection table.
Slim type. For holding, positioning, and chattering the table. It is a normally closed type. Compact design. Easy to install in existing systems. No design changes are required, such as extending the linear guideway rails or changing the table size. The LKPS has a sensor slot for magnet sensors. ... Read More
Operating Temperature Range (℃) -10～70 Type of Control Pneumatic / always closed Response Time (seconds) max. 0.06 Service Life (Clamp life) 5 million times
It is a plate to align the height of [[LBHS]] with the height of the carriage. It may be required depending on the combination of [[LBHS]] and the linear guideway. Please check the selection table.
Positioning and fixing can be done at the same time. Lock / unlock is obvious. Clamping with a taper pin enables simultaneous positioning and fixing without rattling. You can visually check the status from the marks (ON, MID, OFF) on the main unit and the position of the knob. When the knob is in... Read More
Material (Main Unit) SCM440 Material (Knob) Polyamide (glass fiber reinforced) Surface Treatment (Main Unit) Electroless nickel plating Clamping power (N) 170 Color (knob) Black Material (indicator) Aluminum alloy (A5056) Material (taper pin) SCM435 Surface treatment (indicator) Anodized surface treatment Surface treatment (taper pin) Electroless nickel plating Color (indicator) Red
Positioning and fixing can be done at the same time. Screw mounting type. Clamping with a taper pin enables simultaneous positioning and fixing without rattling. The main body can be attached simply by processing tap holes. Not only can it be used with a taper bush, but it can also be used only w... Read More
Material (Main Unit) SCM440 Mass (g) 70 Material (Knob) Polyamide (glass fiber reinforced) Surface Treatment (Main Unit) Electroless nickel plating Clamping power (N) 170 Color (knob) Black Material (indicator) Aluminum alloy (A5056) Material (taper pin) SCM435 Surface treatment (indicator) Anodized surface treatment Surface treatment (taper pin) Electroless nickel plating Color (indicator) Red
Positioning and fixing can be done at the same time. Lock / unlock is obvious. Clamping with a taper pin enables simultaneous positioning and fixing without rattling. You can visually check the status from the marks (ON, MID, OFF) on the main unit and the position of the knob. When the knob is in... Read More
Material (Main Unit) SCM440 Mass (g) 60 Material (Knob) Polyamide (glass fiber reinforced) Surface Treatment (Main Unit) Electroless nickel plating Clamping power (N) 140 Preload None Color (knob) Black Material (indicator) Aluminum alloy (A5056) Material (taper pin) SCM435 Surface treatment (indicator) Anodized surface treatment Surface treatment (taper pin) Electroless nickel plating Color (indicator) Red
For linear shafts. For holding, positioning, and chattering the table. It is a normally open type. When supplying air pressure: Clamps the shaft. When air pressure is discharged: Open the clamp. In addition to linear shafts, it can also be used for round shafts. [[MKR-1600-A]] has changed the par... Read More
Applicable shaft diameter (Φmm) 16 Holding power (N) 650
Slim type. With brake mechanism. It can also be used for table holding, positioning, and chatter prevention. It is a normally closed type. When supplying air pressure: Open the clamp. When air pressure is discharged: The rail of the linear guideway is clamped by the force of the spring. Compact d... Read More
Operating Temperature Range (℃) -10～70 Type of Control Pneumatic / always closed Response Time (seconds) max. 0.06
Slim type. For holding, positioning, and chattering the table. It is a normally open type. When air pressure is supplied: Clamps the rail of the linear guideway. When air pressure is discharged: Open the clamp. Compact design. Easy to install in existing systems. No design changes are required, s... Read More
Specification (Call of applicable rail) + # 15 to # 55 Operating Temperature Range (℃) -10～70 Type of Control Pneumatic / always closed Response Time (seconds) max. 0.06 Service Life (Clamp life) 5 million times
For linear shafts. For holding, positioning, and chattering the table. It is a normally closed type. When supplying air pressure: Open the clamp. When air pressure is discharged: The shaft is clamped by the force of the spring. In addition to linear shafts, it can also be used for round shafts.
Positioning and fixing can be done at the same time. Screw mounting type A clamp with a taper pin that enables simultaneous positioning and fixing without rattling. The main body can be attached simply by processing tap holes. Not only can it be used with a taper bush, but it can also be used onl... Read More
Material (Main Unit) SCM440 Mass (g) 45 Material (Knob) Polyamide (glass fiber reinforced) Surface Treatment (Main Unit) Electroless nickel plating Clamping power (N) 140 Preload None Color (knob) Black Material (indicator) Aluminum alloy (A5056) Material (taper pin) SCM435 Surface treatment (indicator) Anodized surface treatment Surface treatment (taper pin) Electroless nickel plating Color (indicator) Red
THK LM Rail Mounting Hole CapIf the LM rail mounting holes of the LM Guide are clogged with chips or foreign matter, they may enter the inside of the LM block. In such a case, the LM rail mounting hole can be closed with a special cap to prevent foreign matter from entering. The C type cap for the LM rail mounting hole uses ... Read Morefrom S$0.32Min. 2 days
