訂單總金額超過 * S$200* 免運費

噴霧,油,潤滑脂,膠粘劑,修理,焊接用品

排序:
共 3,446 條結果, 第 1 - 30 條
顯示: 30 60 90
視圖: 網格視圖 列表視圖
焊接衡量WGU-7M
SK
$89.99
ADD TO CART
Undercut Measuring Range (mm): 25, Pricision: Length accuracy +/-1 Angular accuracy +/-2degree, Dimension (mm): 95x68, Thickness (mm): 1.5, Material: Stainless steel (SUS420J2), Type: Welding gauge
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接儀器 > 焊接儀表
低碳鋼用氬弧焊焊條
MonotaRO
18.99 - $45.99
Caution: During welding , If you inhale the generated gas or fumes, it may cause damage to your health . So please use exhaust , ventilation or wear protective equipments ., During welding , If you inhale the generated gas or fumes, it may cause damage to your health . So please use exhaust , ventilation or wear protective equipments ., Purpose: Welding of car, bridge, lightweight steel frame, and construction., Welding of car, bridge, lightweight steel frame, and construction., Standard: JISZ3211 D4303 equivalent product
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊條 > 用於低碳鋼和高強度鋼
地線夾
Sanritsu Electric Industry
4.83(6)
25.99 - $43.99
Welding Current (A): 300, Weight (g): 435, Length (mm): 235
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接電纜和連接接頭,其他 > 夾具·接地夾 > 持有人
全塑膠注油器 縫紉機型
FURUPLA
$1.99
ADD TO CART
Nozzle Length (cm): 5.2, Point Bore Diameter (mm): 0.5, Capacity (mL): 35, TRUSCO Part Number: 293-9142
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 噴霧·油·油脂 > 油罐,油罐,噴霧瓶 > 歐拉
噴嘴
FURUPLA
4.25(4)
$6.99
ADD TO CART
Compatible: #3250
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 噴霧·油·油脂 > 油罐,油罐,噴霧瓶 > 噴霧瓶
J形電纜接頭
Sanritsu Electric Industry
3.50(2)
34.99 - $139.99
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接電纜和連接接頭,其他 > 焊接接頭 > 電纜接頭
角凹槽計量器WGA-65
SK
$169.99
ADD TO CART
Measurement Pricision: +/- 0.5 degree (angle), Weight (g): 73.5, Material: Stainless steel (SUS410), TRUSCO Part Number: 412-1678, Specification: Open tip (bevel) angle: 25 - 65 degree (minimum reading 0.5 degree) Tilt angle of the stud after welding joint: 70 - 110 degree
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接儀器 > 焊接儀表
普通用銀焊料
Shinfuji Burner
$27.99
ADD TO CART
Tensile Strength (kgf/mm2): 45, Dimension (phi x mm): 1.0x300, Allowable Temperature (degreeC): 745, TRUSCO Part Number: 376-9160, Ingredients: 35% Silver, 0% cadmium
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 錫焊·銅焊·氣焊焊條 > 釬焊材料
焊縫量規
FUJI TOOL
4.00(1)
$91.99
ADD TO CART
Measurement Range (degree): (Bevel groove angle measurement) 0-85 (five tovey) (general angle measurement) 0-50 (five tovey), Pricision (mm): 0.2 Within, Measuring Range (mm): (Measured flat-fillet weld overlay)20 (Swollen throat thickness measurement)20 (Measurement of plate-round bar)20 (Hole diameter measurement route interval and crevice) 0.5 - 10(0.5tovey), Material: Stainless material, Type: Welding gauge, Description 2: To any measurement of welding work
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接儀器 > 焊接儀表
掌上型丙烷割槍用割槍嘴
NISSAN TANAKA
16.99 - $17.99
Gas: Propane, Compatible: Tanaka small LPG cutting torch Tanaka medium LPG cutting torch
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 氣體熔斷・焊接 > 吹管和焊接技巧 > 彈坑
Winning送風槍
Matsuden
$269.99
ADD TO CART
Weight (g): 650, Dimension (mm): 32phi x 200 x 140, Compatible: 51, 47, 15N, M sharable, Description: diaphragm noise not to be worried about, is the blower type.
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接機・氣焊機 > PVC加工機
焊接規
TRUSCO
5.00(1)
38.99 - $239.99
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接儀器 > 焊接儀表
銀焊料
TRUSCO
4.75(4)
58.99 - $219.99
Caution: Always use silver soldering flux (TRZ-200)., Purpose: Brazing of dissimilar metals of iron, brass, stainless steel, silver and copper, Tensile Strength (N/mm2): 539, Melting Point (degree c): 780, Length (mm): 500, Material: 40% Silver content
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 錫焊·銅焊·氣焊焊條 > 銀釬桿
帶加熱器壓力調節器
CHIYODA SEIKI
$379.99
ADD TO CART
Caution: Cannot be used to siphon gas cylinder., Cannot be used to siphon gas cylinder., Purpose: Arc welding, beverages, food industry, casting industry, promotion of plant cultivation, industrial, etc., Arc welding, beverages, food industry, casting industry, promotion of plant cultivation, industrial, etc., Heater's storage capacity (W): 190, Flowmeter (L/min): 2 - 25, Adjustment Pressure (MPa): 0.1 - 0.3, Secondary Side Pressure Guage (MPa): 0 - 0.6, Valve-Inlet Pressure (MPa): tless than 14.7 , Valve-Inlet Pressure Meter (MPa): 0 - 25, Gas: Carbon dioxide as the primary, Power Source (AC V): 100, Cord Length (m): 2.0, Peak Flow Rate (L/min): 25, Weight (kg): 2.06, Connection Diameter: Inlet side of :W22 mountain (right) 14 bags per Nut gasket, EXIT SIDE :M12x1... phi 6 6 HOSE WITH FI...
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接氣體軟管和調節器耦合器 > 氣體調整器
小型氣焊槍
SAKAGUCHI
4.67(3)
$129.99
ADD TO CART
Purpose: For welding of 5 mm of sheet metal, For welding of 5 mm of sheet metal, Welding Capability (mm): 0.5 - 3, Gas: Acetylene type, Weight (g): 510, Overall Length (mm): 370, Accessories: Five (No.50, 70, 100, 140, 200 1 each)
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 氣體熔斷・焊接 > 吹管和焊接技巧 > 焊接設備
鋁用氬焊條
NIPPON WELDING ROD
5.00(2)
149.99 - $179.99
Purpose: For Al-Mg alloys, AWS Standards: A5.10 R5356, JIS Standard: Z 3232 A 5356-BY, Length (mm): 1000
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > TIG焊條 > 鋁用
CO2焊槍用節流器
Panasonic Smart Factory Solutions
4.00(2)
38.99 - $55.99
Number of Holes: 8(phi2.0mm)
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊槍 > CO2焊接焊槍用交換零件 >
氧氣用調整器 SS小型
YAMATO SANGYO
5.00(1)
$169.99
Weight (kg): 1.1
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接氣體軟管和調節器耦合器 > 氣體調整器
電極
DAIHEN
5.00(6)
68.99 - $95.99
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊槍 > 空氣等離子焊槍用交換零件 > 電極
遮光眼鏡 No.337W
YAMAMOTO
23.99 - $24.99
Material (lens): Polycarbonate, Material (frame): Plastic, Frame Color: Green, Frame: Plastic, Weight (g): 43, Size: W157xH64xD150(mm)
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接面具,著色眼鏡 > 擋光眼鏡
氬氣體壓力調整器 高・可選
CHIYODA SEIKI
$359.99
ADD TO CART
Flowmeter (L/min): 41695, Adjustment Pressure (MPa): 0.1 - 0.6, Secondary Side Pressure Guage (MPa): 0 - 1, Valve-Inlet Pressure (MPa): 14.7 below, Valve-Inlet Pressure Meter (MPa): 0 - 25, Compatible Gas: Ar (argon gas), Connection: Entrance: W22-14 right (standard) exit: M12x1.0 (phi6 hose fitting), Peak Flow Rate (L/min): 100, Weight (kg): 1.4, Specification: Brass
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接氣體軟管和調節器耦合器 > 氣體調整器
防水標記粉筆
TRUSCO
$11.99
Weight (g): 19, Dimension (mm): phi15x100
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 滑石鉛筆和標記 > 粉筆
焊錫助焊劑
Shinfuji Burner
4.12(8)
$9.99
ADD TO CART
Type: Liquefied, TRUSCO Part Number: 376-9275, Compatible: Silver solder (RZ-100, RZ-107, RZ-108, RZ-150) Phospor bronze solder (RZ-102)
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 錫焊·銅焊·氣焊焊條 > 通量
低碳鋼焊條〜550MPa級鋼
Kobe Steel
57.99 - $249.99
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊條 > 用於低碳鋼和高強度鋼
通用小型壓力調整器
YAMATO SANGYO
5.00(2)
$129.99
ADD TO CART
Standard Flow rate (m3/h): 25(P1=2.1MPa, P2=0.8MPa), Low Gauge Pressure (MPa): 2.5, High Gauge Pressure (MPa): 25, Secondary-side Working Range (MPa): 0.2 - 0.99, Primary-side Working Range (MPa): - 15, Gas: Oxygen, Model/Type: Kanto type (hexagon cap nut type), Weight (kg): 1.2, Connection Diameter: Inner outlet: W22-14crest/ Outer outlet: 8phi hose opening
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接氣體軟管和調節器耦合器 > 氣體調整器
LPG軟管
TOGAWA RUBBER
3.25(4)
45.99 - $83.99
Approximate Mass (g/m): 190, Reinforcing Layer: 2S, Display: LMN, Outer Diameter (phi mm): 16.5, Working Pressure (MPa): 2.0, Inner Diameter (phi mm): 9.5, Color: Orange
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接氣體軟管和調節器耦合器 > 焊接氣體軟管
低碳鋼 到550MPa級鋼用焊條
Kobe Steel
25.99 - $239.99
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊條 > 用於低碳鋼和高強度鋼
LP調整器
CHIYODA SEIKI
$199.99
ADD TO CART
Inlet Pressure (MPa): less than 2.0, Adjustment Pressure (MPa): 0.02 - 0.15, Secondary Side Pressure Guage (MPa): 0 To 0.25 (No primary side pressure gauge), Standard Flow rate (m3/h): 4 (normal condition), Gas: Propane, Weight (kg): 0.75, Shape: Entrance: For W22.5 mountain 14 (the left) LP exit: M16-P1.5 (the left) 3/8 (phi9) hose mouth, Material: main unit: C3771B Diaphragm: CR Seat: C3604B, Caution: Do not use below 5 degree C air temperature. Cannot be used in the removed fluid from siphon tank etc.
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接氣體軟管和調節器耦合器 > 氣體調整器
半自動電焊機Arcury120
STAR ELECTRIC MANUFACTURING (SUZUKID)
3.50(2)
$1,109.99
ADD TO CART
Compatible Plate Thickness: Non-gas mild steel: 0.8 - 6.0mm (0.8 at 100V 15A use - 3.0mm) (6mm maximum at 100V 30A use) non-gas stainless steel: 0.8 - 3.0mm 0.8 in (100V 30A use - 2mm) solid mild steel: 0.7 - 5.0mm 0.7 in (100V 15A use - 3mm) so, Welding Process: Non-gas welding / mild steel, stainless MAG welding / mild steel, stainless MIG welding / aluminum CO 2 welding / mild steel, Rating Usage (%): 10, Power Consumption (kW): 2.5, Power Source (single phase/V): 100, Cycle(Hz): 50/60 combined, Type: [100V] only semiprofessional, professional non-gas MIG / MAG combined, Weight (kg): 20, Set Contents: Earth clip (1.2m body with code) torch (code body with 1.8m) power cord (1.7m body with) 2P/100V adapter wire brush and chipping hammer-shielding surfaces (filter p...
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接機・氣焊機 > 半自動焊接機
Speed Glass 自動變光焊接面罩 9100系列
ThreeM 3M
479.99 - $689.99
Purpose: Temporary welding. Polish welding., Shading Degree when Power Off: #5, Light Shielding Degree when Radioscopy: #3, Light Shieling Speed (sec): 1/10000 (at 23 deg C ), Protection: UV/IR/#13 (permanence), Storage Temperature Range (degree c): -30 - +70, Return Speed (sec): 0.04-0.13 (variable / 23 deg C o'clock), Auto Power-off: 60 minutes, Degree of Shading: # 5, #8, and #9-13 (variable), Operating Temperature Range (deg C): -5 - +55, Type: Liquid crystal filter
分類 噴霧,油,潤滑脂,膠粘劑,修理,焊接用品 > 焊接用品 > 焊接面具,著色眼鏡 > 焊接表面(自動變暗表面) > 主要單位

1 2 3 4 5 6 7 8 9 10 ...115